Calipers & Dividers

Lightweight, ergonomic designLarge, easy-to-read LCD displayAuto shut-off function after 30 minutes

Lightweight, ergonomic designLarge, easy-to-read LCD displayAuto shut-off function after 30 minutes

New designed dial movement for ultra smooth sliding and high shock protectionTitanium nitride (TiN) coating is applied to the sliding surface to increase wear resistanceLock screw for dial bezel and for holding the sliding jaw position

Large, easy-to-read LCD numbersOn/Off and zero buttonPocket clip

Sized to slip in your pocketEtched and filled graduations

Carpenter quality compass is made of long lasting die cast, rust-resistant metalAdjustment is spring tension

Handy pocket slide caliper with inside and outside reading in 16ths and 32ndsDecimal equivalents table on back

Legs are hardened tempered steelHardened and tempered bow spring and fulcrum screwAdjustable self-seating washer to permit quick and positive adjustment

Positive wingnut adjustment

With 6 in off-center eccentric points to provide fine adjustment

Legs are hardened tempered steelHardened and tempered bow spring and fulcrum screwAdjustable self-seating washer to permit quick and positive adjustment

Heads feature radius set points cast in alignment with marking pointer for easy settingEquipped with 1/4 in screws and squared on back for perpendicular alignmentStationary head holds 1/4 in case hardened center point

Contact ends fully rounded to give accurate dimensions

The rounded faces of the jaws are ideal for accurate ID measurementParallax-free vernier scale type is available for easy and positive measurement

Large and clear LCD readoutThe ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements

Lightweight, employs CFRP (Carbon Fiber Reinforced Plastics) in the beam and jawsHighly durable and easy to handleDirect readout of ID measurements from the LCD

Lightweight, employs CFRP (Carbon Fiber Reinforced Plastics) in the beam and jawsHighly durable and easy to handleDirect readout of ID measurements from the LCD

The slider moves only when the spindle-loaded thumb clamp is depressedCan measure OD, ID, depth and stepsSupplied with vinyl holster in fitted carton

The slider moves only when the spindle-loaded thumb clamp is depressedCan measure OD, ID, depth and stepsSupplied with vinyl holster in fitted carton

Large and clear LCD readoutThe ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements

Contact ends fully rounded to give accurate dimensions

Lightweight, employs CFRP (Carbon Fiber Reinforced Plastics) in the beam and jawsHighly durable and easy to handleDirect readout of ID measurements from the LCD

Large and clear LCD readoutThe ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements

The rounded faces of the jaws are ideal for accurate ID measurementSPC outputSupplied in a fitted plastic case

An improved joint, designed so the tension can be adjustedThe legs are made from a high-grade steelTension does not change with opening and closing of legs

Legs are made from flat stockFulcrum stud is hardened and has a smooth bearing surfaceStrong, flexible bow springHigh-grade steel construction

Legs are made from flat stockStrong, flexible bow springFulcrum stud is hardened and has a smooth bearing surfaceHigh-grade steel construction

Straight measuring surface for outside measurements, rounded nibs for inside or hole measurementsKnurled clamp screw with left hand thread for one hand operationCompact, pocket sizeKnurled thumb pieces activate the slideSlide stop prevents disassembly of...

Quadrant adjusting nut for fine adjustmentsSturdy constructed joint with quadrant, eliminates side deflection of the legsForged steel, tempered and polished legsRemovable, adjustable point can be exchanged for a pencilBall points may be used with this...

Knife-edge contacts for both inside and outside measurementsOne hand use with the thumb-operated, fine adjustment rollLock screw for dial bezelLock screw for holding the sliding jaw in positionPositive, split-gear anti-backlash control

Used to measure the distance between points that are too great to be reached with dividersThe heads are die cast and have hardened, forged steel divider pointsThe points screw into the heads, and the pencil socket accompanying each set of trammel heads...

Legs are made from flat stockStrong, flexible bow springFulcrum stud is hardened and has a smooth bearing surfaceHigh-grade steel construction

Legs are made from flat stockFulcrum stud is hardened and has a smooth bearing surfaceStrong, flexible bow springHigh-grade steel construction

Legs are made from flat stockFulcrum stud is hardened and has a smooth bearing surfaceStrong, flexible bow springHigh-grade steel construction

Induction type linear encoder systemLock to hold the slide in positionZero at any positionManual on/off, auto off

Knife-edge contacts for both inside and outside measurementsOne hand use with the thumb-operated, fine adjustment rollLock screw for dial bezelLock screw for holding the sliding jaw in positionPositive, split-gear anti-backlash control

Long 50-division vernier scalesFlush fitting of the vernier scales to the main scaleOpen-face designScrew-type adjusting nutLock nut to hold measurements

Induction type linear encoder systemLock to hold the slide in positionZero at any positionManual on/off, auto off

An improved joint, designed so the tension can be adjustedThe legs are made from a high-grade steelTension does not change with opening and closing of legs

Legs are made from flat stockFulcrum stud is hardened and has a smooth bearing surfaceStrong, flexible bow springHigh-grade steel construction